Interline 904

INTENDED USES

Suitable for the carriage of an extensive range of aggressive cargoes including solvents (including methanol) and chemicals, clean and dirty petroleum products, vegetable and animal oils. For use at Newbuilding or Maintenance & Repair.

color	TCA932-Pink, TCA933-Buff, TCA934-Grey
Finish/Sheen	Semi-gloss
Part B (Curing Agent)	TCA935
Volume Solids	48% ±2% (ISO 3233:1998)
Mix Ratio	6.30 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness	90 microns dry (188 microns wet)
Theoretical Coverage	5.33 m2/litre at 90 microns dft, allow appropriate loss factors
Method of Application	Airless Spray, Roller, Brush
Flash Point	Part A 23°C; Part B 38°C; Mixed 31°C
Induction Period	Not required

Drying Information

	Substrate Temperature
	5°C	10°C	25°C	35°C
Touch Dry [ISO 1517:73]	8 hrs	6 hrs	3 hrs	90 mins
Hard Dry [ISO 9117:90]	18 hrs	14 hrs	7 hrs	4 hrs
Pot Life	5 hrs	4 hrs	3.5 hrs	1.5 hrs

Note

See Limitations section when Intershield 300 is used as part of an Intersleek scheme.

Overcoating Data

see limitations

Overcoated By	Substrate Temperature
	5°C		10°C		25°C		35°C
	Min	Max	Min	Max	Min	Max	Min	Max
Interline 850	36 hrs	35 days	30 hrs	34 days	16 hrs	28 days	12 hrs	14 days

REGULATORY DATA

497 g/lt as supplied (EPA Method 24)
387 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)

Note.

VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.

Note.

MIL-PRF-4556 (White and Buff shade only)

CERTIFICATION

When used as part of an approved scheme, this material has the following certification:

• Food Contact - Carriage of Grain (NOHA)

Consult your International Paint representative for details.

 

SYSTEMS AND COMPATIBILITY

Consult your International Paint representative for the system best suited for the surfaces to be protected. When using in cargo or grey water tanks, consult the Interline 904 Cargo Tank or Grey Water Tanks Application Guidelines.

SURFACE PREPARATIONS

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

NEWBUILDING/MAJOR REFURBISHMENT

Where necessary, remove weld spatter and smooth weld seams and sharp edges. Abrasive blast clean to Sa21⁄2 (ISO 8501-1:2007). If oxidation has occurred between blasting and application of Interline 904, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process, should be ground, welded, or treated in the appropriate manner.

REPAIR

Consult International Paint.

APPLICATION

Mixing

Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.

Thinner

Not Recommended. Use International GTA713 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Recommended Tip Range 0.46-0.58 mm (18-23 thou) Total output fluid pressure at spray tip not less than 176 kg/cm2 (2500 p.s.i.)

Conventional Spray

Application by conventional spray is not recommended.

Brush

Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Roller

Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.

Cleaner

International GTA713

Work Stoppages and Cleanup

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA713. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Clean all equipment immediately after use with International GTA713. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

Welding

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

SAFETY

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

LIMITATIONS

International Paint should be consulted to confirm that the tank coating is suitable for the range of cargoes to be carried. The drying times and overcoating intervals may alter due to various on-site factors such as tank configuration and ventilation rates. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

UNIT SIZE

Unit Size	Part A		Part B
	Vol	Pack	Vol	Pack
20 lt	17.25 lt	20 lt	2.75 lt	3 lt

UNIT SHIPPING WEIGHT

Unit Size	Unit Weight
20 lt	29.49 Kg

STORAGE

Shelf Life

12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.