A high solids, high performance, TBT free, low friction, self polishing copolymer (SPC) antifouling. Particularly suitable for use where solvent emissions need to be reduced.
INTENDED USES
Specifically designed for Deep Sea Vessels. For use at Maintenance & Repair.
color | BEA754-Brown, BEA757-Red, BEA744-Brown, BEA747-Red (only available in European non-regulated countries) |
Finish/Sheen | Not applicable |
Part B (Curing Agent) | Not applicable |
Volume Solids | 54% ±2% (ISO 3233:1998) |
Mix Ratio | Not applicable |
Typical Film Thickness | Range: 75 - 200 microns dry (139 - 370 microns wet) may be specified depending upon end use. |
Theoretical Coverage | Range: 7.2 - 2.7 m²/litre at 75 - 200 microns dft, allow appropriate loss factors |
Method of Application | Airless Spray, Brush, Roller |
Flash Point | Single Pack 25°C |
Drying Information
Substrate Temperature | ||||
-5°C | 5°C | 25°C | 35°C | |
Touch Dry [ISO 9117/3:2010] | 120 mins | 60 mins | 40 mins | 30 mins |
Before Flooding 0-36 Month Schemes | 30 hrs | 20 hrs | 16 hrs | 10 hrs |
Before Flooding 48-60 Month Schemes | 48 hrs | 36 hrs | 24 hrs |
note
For 0-36 month schemes the times before flooding must revert to the times for 48-60 month schemes if:
1) the antifouling scheme includes any single coat greater than 150 microns, and
2) the vessel service speed is greater than 15 knots
For 48-60 month schemes the times before flooding can revert to the times for 0-36 month schemes if:
1) no single coat is applied at more than 150 microns, or
2) the vessel service speed is less than 15 knots
Overcoating Data
see limitations
Overcoated By | Substrate Temperature | |||||||
-5°C |
5°C | 25°C | 35°C | |||||
Min | Max | Min | Max | Min | Max | Min | Max | |
Intersmooth 7460HS SPC 0-36 Month Schemes |
12 hrs | 28 days | 6 hrs | 28 days | 4 hrs | 28 days | 3 hrs | 28 days |
Intersmooth 7460HS SPC 48-60 Month Schemes |
- | - | 18 hrs | 28 days | 12 hrs | 28 days | 9 hrs | 28 days |
REGULATORY DATA
VOC 425 g/lt as supplied (EPA Method 24) 226 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)
Note.
VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
EPA
This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26).
CERTIFICATION
Consult your International Paint representative for details.
SYSTEMS AND COMPATIBILITY
Consult your International Paint representative for the system best suited for the surfaces to be protected.
SURFACE PREPARATIONS
Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
MAJOR REFURBISHMENT
Intersmooth 7460HS SPC should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intersmooth 7460HS SPC must be applied within the overcoating intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc. should be prepared to the specified standard (eg. SSPC-SP10) and primed prior to the application of Intersmooth 7460HS SPC.
REPAIR
Application of Intersmooth 7460HS SPC over self: Clean the entire area with close high pressure fresh water washing using a fan-jet lance held close to the surface (3,000 p.s.i., 211 kg/cm²) as soon as the vessel enters dock and before it dries out. Consult the recommended anticorrosive primer system and apply Intersmooth 7460HS SPC within the overcoatng interval specified for the primer (consult the relevant primer data sheets).
Application of Intersmooth 7460HS SPC over International Paint TBT-Free, International Paint Intersmooth SPC or competitors antifoulings: Consult your International Paint representative for specific recommendations. Page 2 of 4 Ref:
APPLICATION
Mixing
This material is a one pack coating and should always be mixed thoroughly with a power agitator before application.Thinner
Not Recommended. Use International GTA007 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.
Airless Spray
Recommended
Tip Range 0.54-0.80 mm (21-31 thou)
Total output fluid pressure at spray tip not less than 190 kg/cm² (2700 p.s.i.)
Conventional Spray
Application by conventional spray is not recommended.Brush
Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.
Roller
Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.
Cleaner
International GTA007
Work Stoppages and Cleanup
Thoroughly flush all equipment with GTA007. All unused material should be stored in tightly closed containers. Partially filled containers may show a viscosity increase of the material after storage. Material should be filtered prior to use.
Welding
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
SAFETY
All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.
LIMITATIONS
Coating lifetime is directly proportional to thickness applied. Performance of the product is dependent upon the specified film thickness being achieved.
On immersion, Intersmooth 7460HS SPC will exhibit a slight colour change. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.
UNIT SIZE
Unit Size | ||
Vol | Pack | |
20 lt | 20 lt | 20 lt |
For availability of other unit sizes consult International Paint
UNIT SHIPPING WEIGHT
Unit Size | Unit Weight |
20 lt | 38.6 Kg |
STORAGE
Shelf Life | 12 months at all temperatures. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition. |