eng Русский язык

Tank Cleaner-A

TANK CLEANER - A is a highly concentrated liquid blend of superior, innovative constituents which contribute to the efficient removal and cleaning of cargo tanks, fuel oil tanks and tank lines from oil contamination, fuel residues and sludge deposits.

It contains biodegradable raw materials and it’s a powerful cleaning product. It may safely be applied to all kinds and types of metal surfaces painted or not, it is non corrosive and it has non known effect on rubber and plastic parts. Furthermore, it may be used as a general degreaser in special situations where optimum results are sought.

Characteristics, Advantages & Applications

  • Concentrated degreasing solution, ideal for use in cleaning cargo tanks, deep tanks, bilges and pipelines.
  • Non-corrosive and non-toxic.
  • Consists of water-based raw materials.
  • No known effect on rubber or plastic compounds.
  • Can be used as a general degreaser in very difficult cleaning situations.
  • May be applied to all kinds and types of metal surfaces, painted or not.
  • May be combined with a broad range of products.
  • Cost effective, easy to apply and use.

Physical Properties

TANK CLEANER - A is a liquid solution that contains an aromatic solvent, non-ionic, surface-active agents, corrosion inhibitor and biodegradable, water-based raw materials.

Appearance / Color Light yellow liquid
Odor Slight Aromatic
Specific gravity 0.90/20°C
Flash Point >60°C
Stability Very Stable
Order No Size (in litres) Container
832531 25 Steel drum
832131 210 Steel drum

Application and Use

A. Dosing Procedure

The quantity of TANK CLEANER - A to be used is proportional to the tank capacity, the level of contamination and the degree of cleaning required, as such; appropriate dosing can be decided by consulting the table found below.

NOTE: The dosage to be used must be based on the total tank capacity and not on the water percentage to be ballasted in the tank.

BALLAST TANK
CAPACITY (tones)
TANK CLEANER-A QUANTITY (litres)
MINIMUM NORMAL MAXIMUM
2,5 2 4 6
5 4 8 12
10 8 16 24
15 12 24 36
20 16 32 48
25 20 40 60
30 24 48 72
40 32 64 96
50 40 80 120
75 60 120 180
100 80 160 240
200 160 320 480
250 200 400 600
300 240 480 720
400 320 640 960
500 400 800 1200
600 480 960 1440
700 560 1120 1680
800 640 1280 1920
900 720 1440 2160
1000 800 1600 2400

B. Cleaning Procedure

Preparation: Before applying TANK CLEANER - A, prepare the tanks that are to be cleaned by washing them first (if this is possible), with a high-pressure warm water supply.

When not at sea: Determine the quantity of TANK CLEANER - A to be used and fill 75% of tank capacity with seawater.

At the end of the three days time, deballast the tanks of the cleaning solution and rinse clean with seawater by ballasting and deballasting until the water flow becomes clear.

Note: In cases, where tanks are heavily stained or contaminated, the cleaning procedure must be repeated, as described above.

Rock and Roll method: This method is applicable for tank cleaning at sea. Fill the tank with 0.1-0.3% of TANK CLEANER - A and leave solution to act for 2-6 hours. This will enable the solution to soften, penetrate and dissolve the hard bottom deposits. Then fill the tank with seawater to 30% of total capacity and let the solution stand for approximately 1-2 days. During this period, cleaning will be initiated due to wave motion. After, fill the tank with seawater to 60% of total capacity and let the solution act for long enough, so that complete cleaning can be accomplished, due to wave motion/natural agitation. Afterwards, discharge solution from tank and then rinse off by filling tank 1-2 times its capacity with seawater.

Note that TANK CLEANER - A must always be fed to the tank and then to the bunkers.

Recirculation Method: It is recommended to use the desired solution according to the degree of contamination and number of tanks to be cleaned with this solution. For this reason the dose rates and results of the cleaning may vary, but as minimum dosage a 0.5% solution of the product must be used. The best result is achieved around 70°C

Slop water should be pumped ashore or should be pumped to ship’s slop tanks after finishing with the cleaning procedure.

General Cleaning: For general cleaning applications, TANK CLEANER - A may be used by brushing, soaking/immersion or any other conventional method that the user believes to be suitable for the situation at hand.

Safety and Handling

HANDLING Handle with care. Store in a dry, cool and well ventilated environment.
SAFETY IMMEDIATE ACTIONS
Eye Contact Avoid Eye contact. Otherwise, flush with plenty of water for a few minutes. Seek medical attention.
Skin Contact Avoid Skin contact. Otherwise, wash contaminated area thoroughly with water. Seek medical attention.
Inhalation Do not breathe gas/vapors. Otherwise, seek fresh air source at once. Seek medical attention. In case of insufficient ventilation, wear suitable respiratory equipment.
If Swallowed Avoid ingestion. Otherwise, consume a considerable quantity of water. Do not induce vomiting. Seek medical attention.
GENERAL INSTRUCTIONS Avoid spillage, splashing and mishandling. Precautionary measures for body protection are strongly recommended before use.

Read the Material Safety Data Sheet before using this product.

For detailed information on safety and health, please refer to Material Safety Data Sheet and/or Product Label.

Яндекс.Метрика