Advanced Bearing & Circulating Oils
Performance Benefits
Long oil life – Maintenance saving
The use of highly stable synthetic base oils in conjunction with a robust rust and oxidation inhibitor package helps provide excellent oxidation and thermal stability. This provides Shell Morlina S4 B with extending maintenance capability compared to conventional oils.
In addition it resists the formation of harmful products of oxidation at high operating temperatures, to help maintain system cleanliness and therefore reliability of the equipment.
Excellent wear & corrosion protection
Shell Morlina S4 B has been formulated to provide excellent anti-wear performance and provides high levels of wear protection for plain and rolling element bearings and moderately loaded gearboxes, compared to mineral oil-based products. This helps provide superior gear and bearing component life.
In addition it also provides outstanding rust and corrosion protection of all metal surfaces.
Enhancing system efficiency
Shell Morlina S4 B can help improve the efficiency of lubrication in bearing and circulating systems. The superior low temperature performance and reduced change in viscosity with increase in temperature in comparison to mineral oil-based products provides better lubrication at low start-up temperatures and the opportunity for energy savings through reduced pumping and flow losses during normal operating conditions. Rapid water shedding and air release properties further enhance the efficiency of the lubrication system by helping maintain critical oil films between loaded components.
Applications
Severe operating conditions
Shell Morlina S4 B is recommended for systems incuding moderately loaded gearboxes, operating under severe conditions such as low or high temperatures or with wide temperature variations.
Lubricated for life systems
The long oil life of Shell Morlina S4 B makes is suitable for use in certain ‘lubricated-for-life’ systems.
Bearing and circulating oil systems
Suitable for use in systems containing plain or rolling element bearings, including those highly loaded bearings found in such as those found in cement or quarrying applications.
Specifications and Approvals
Shell Morlina S4 B oils meet the requirements of:
- ISO 12925-1 Type CKS specification.
- Alfa Laval Group D gearbox applications
- Aerzen Maschinenfabrik GmbH Blower Applications
- Baltimore Aircoil Gear Boxes
- Cincinnati Machine Various P applications
- David Brown Table H applications
- Emerson Power Transmission
- GEA Westfalia Separator GmbH
- Renold Gears (various applications)
- Sharpe E-series worm gear reducers
- Winsmith (Peerless-Winsmith Inc) Worm gear reducer
Seal & Paint Compatibility
Shell Morlina S4 B is compatible with all seal materials and paints normally specified for use with mineral oils.
Change over procedure
Shell Morlina S4 B is compatible with petroleum mineral oils and no special change-over procedure is necessary. However, to realise the full benefits, it should not be mixed with other oils. It is also advisable to ensure that oil systems are clean and free from contamination to optimse potential service life.
Health and Safety
Guidance on Health and Safety is available on the appropriate Material Safety Data Sheet, which can be obtained from your Shell representative.
Protect the Environment
Take used oil to an authorized collection point. Do not discharge into drains, soil or water.
Advice
Advice on applications not covered in this leaflet may be obtained from your Shell representative.
Typical Physical Characteristics
Shell Morlina S4 B | 68 | 100 | 150 | 220 | 320 | 460 | 680 | 1000 | |
ISO Viscosity Grade | ISO 3448 | 68 | 100 | 150 | 220 | 320 | 460 | 680 | 1000 |
Kinematic
Viscosity at 40°C mm2/s at 100°C mm2/s |
ISO 3104 | 68 10.5 |
100 14.0 |
150 19.8 |
220 25.9 |
320 33.8 |
460 45.5 |
680 61.9 |
1000 84.7 |
Viscosity Index | ISO 2909 | 142 | 142 | 149 | 149 | 148 | 155 | 160 | 167 |
Flash Point COC °C | ISO 2592 | 254 | 282 | 236 | 240 | 270 | 274 | 286 | 286 |
Pour Point °C | ISO 3016 | -54 | -54 | -54 | -48 | -45 | -42 | -39 | -36 |
Density
at 15°C kg/m3 Emulsion Test, minutes Foam Test, Seq. II (ml foam at 0/10 minutes) |
ISO 12185 ASTM D1401 ASTM D892 |
857 10 0/0 |
859 10 0/0 |
848 15 0/0 |
853 15 0/0 |
854 20 0/0 |
855 30 0/0 |
857 30 0/0 |
859 30 0/0 |
FZG Load
Carrying Test Failure load stage |
DIN
51354-2 A/8.3/90 |
>12 | >12 | >12 | >12 | >12 | >12 | >12 | >12 |
These characteristics are typical of current production. Whilst future production will conform to Shell's specification, variations in these characteristics may occur.